Home Improvement Skills & Specialties Electrical

How to Shut Off Your Home Gas Supply Valve

By
Bob Formisano
Bob Formisano
Bob Formisano is a licensed architect and builder with nearly 40 years of experience building new homes and restoring older homes. One of his specialties is repairing old systems dating back to the 1920s, including galvanized water pipes, knob-and-tube wiring, and more. His home repair articles for The Spruce span more than 10 years.
Learn more about The Spruce's Editorial Process
Updated on 04/15/22
Reviewed by
Deane Biermeier
Deane Biermeier
Reviewed by Deane Biermeier
Deane Biermeier is an expert contractor with nearly 30 years of experience in all types of home repair, maintenance, and remodeling. He is a certified lead carpenter and also holds a certification from the EPA. Deane is a member of The Spruce's Home Improvement Review Board.
Learn more about The Spruce's Review Board
Natural gas meter and main valve shut off at a suburban home

Brett_Hondow / Getty Images

Shutting off utilities, such as your home's water supply or electrical power, is fairly common—something you do whenever making a repair or upgrade. By contrast, shutting off your natural gas supply is something you may never have to do. Work on branch gas lines in a home is not safe for amateurs and should be left to plumbers or gas company technicians. But most gas companies allow homeowners to shut off the gas at their own meters and even provide instructions for doing this safely. If you have questions about shutting off your home's gas supply at the meter, contact your gas utility provider.

Warning

If there is a strong gas smell in your home, leave the house immediately and call the utility company from outside or from a neighbor's house. Do not attempt to shut off the gas supply at the meter or anywhere else. Even turning on a light switch can ignite a gas explosion inside a house. A strong gas odor indicates a leak, which must be checked out by a utility technician.

Reasons for Shutting Off the Gas

The main shutoff valve controlling your home's natural gas supply may come into play during major construction or renovation involving gas lines or when closing up or shuttering a home. In rare instances, you may need to shut off the gas supply in the event of a natural disaster.

Once the valve is turned off, do not turn it back on by yourself. It must be turned on by a gas company technician. The gas company will likely perform a pressure test on the system and relight all pilot lights in the house as part of turning the gas back on.

Location of the Main Shutoff Valve

The main gas shutoff valve is located near the gas meter supplied by your utility company. Your gas meter may be located outside your home on an exterior wall, or it may be found inside your home on an outside wall—often in a basement or utility area, such as a garage or the mechanical room where the furnace or water heater are located. 

Typically, the valve is located on the supply pipe that rises from the ground and ultimately connects to the meter. The valve appears in the line before the meter so that the gas can be shut off before it reaches the meter. There also may be a second shutoff valve after the meter, between the meter and the house. The correct valve to shut off is the one before the meter.

How to Shut Off the Main Gas Valve

The shutoff valve has a rectangular (or flat-sided) tab that is about 1/2 inch thick; this is what you turn to shut off the gas. When the tab is parallel to the gas pipe, the valve is open and the gas is on. When it is fully perpendicular to the pipe, the valve is closed and the gas is off.

To close the valve, use an adjustable wrench adjusted to fit snugly over the valve tab. You can also use clamping pliers or an open-end wrench. Turn the tab so it is fully perpendicular (90 degrees) to the gas line. It will take only a quarter-turn.

NOTE: Many gas meter valves have a hole in the tab (or on a bracket attached to the tab) that will line up with a corresponding hole in the valve body when the gas valve is in the closed position. The utility company will use the hole to lock the valve in a closed position when the gas account is closed. When the holes in the valve handle are lined up, it indicates the valve is in the off position.